121215 products
Showing 17071-17100 of 121215 products
TEXAS INSTRUMENTS LMC6482 dual CMOS op-amp with rail-to-rail I/O, 1.5MHz, 3V-15.5V, SOIC-8. Ideal for precision signal conditioning.
TEXAS INSTRUMENTS TXS0102 bidirectional voltage translator (1.65-5.5V). Enables 24Mbps data between mixed-voltage systems. VSSOP-8 package.
Energy-efficient LNK304GN-TL off-line switcher IC. PDIP-8 package, 85-265VAC input, for buck, boost & flyback topologies. Low component count.
Enhance your Raspberry Pi 5 with the 52Pi NVDigi audio board, featuring S/PDIF, M.2 NVMe slot, IR receiver, and high-res audio up to 192kHz.
BROADCOM 1-channel SOIC-8 optocoupler with 1Mbps speed, 3.75kV isolation & TTL output. For motor control, power interfaces & signal processing.
ISOCOM 6-pin SMD optocoupler with Triac output, 5.3kV isolation. For motor control, consumer electronics & AC load switching.
APEM Q12 green LED panel indicator, 24 VDC, 12 mm hole, 20 mA, 60 mcd. Ideal for control panels and automation.
Broadcom subminiature high-efficiency red SMD LED, 626nm, wide viewing angle, ideal for space-limited industrial signalling.
24V red LED panel indicator with matt chrome bezel and IP67 rating. For industrial signalling in control panels and machinery. 8mm mount.
Durable Dialight green LED panel indicator for 24V systems. Watertight, high-intensity, and built for industrial, aerospace & automotive use.
VCC transparent light pipe for panel mounting. Transmits & blends LED light with a 160° viewing angle. Easy install.
Open-source prototyping shield for Arduino Mega & Due with reset button, power rails, and DIP area. Ideal for hobbyists and engineers.
Step down 12-24V to 5V with this efficient dual USB buck converter module. Features 3A output, overload protection, and stable power for DIY projects.
Compact DFROBOT holder for 6 AA batteries, featuring a DC 2.1mm power jack. Ideal for electronics projects, sensors & portable devices.
DFROBOT vertical adaptor converts RJ45 to an 8-position screw terminal block. Ideal for electronics prototyping & industrial wiring. 43x33x15mm.
Flexible DFROBOT liquid level sensor for non-conductive containers. Non-contact capacitive design with 3M adhesive tape & IP62 rating.
Upgrade your projects with the PIMORONI Pico Plus 2. Features RP2350B, 8MB PSRAM, 16MB flash & USB-C. Compatible with Pico add-ons.
ISOCOM IS621XSM 6-pin SMD optocoupler with 5.3kV isolation & zero-crossing TRIAC output for motor control & industrial uses.
ISOCOM ISQ203X 4-channel optocoupler with 5.3kV isolation, 225% CTR, and DIP16 package for industrial and computer applications.
ISOCOM SFH615A-3X 1-channel optocoupler. 5.3kV isolation, 50mA forward current, 100% CTR. For industrial & computer systems.
Whadda NodeMcu V2 Lua development board with ESP8266 WiFi. Perfect for IoT prototyping, featuring 10 GPIO pins & breadboard compatibility.
Amplify audio signals up to 8.5x with the Whadda WPM457 Digital Speaker Module. Features SC8002B chip, 2W power, 80dB volume & 5V DC supply.
BOURNS SMCJ12A unidirectional TVS diode, 12V stand-off, 19.9V clamping. Protects power lines, automotive & industrial electronics from transients.
Littelfuse axial leaded Schottky rectifier, 45V, 20A. Features 250A surge current & 150°C max operating temp. Ideal for power supplies.
Low forward voltage Schottky diode, 40V, 2A, SOD-106, ideal for motor control and portable devices.
Taiwan Semiconductor DBLS203G SMD bridge rectifier, 2A, 200V, single phase, surface mount.
VISHAY TRANSZORB SMCJ unidirectional TVS diode, 5V reverse standoff, 9.2V clamping, surface mount. Ideal for automotive & electronics protection.
Wurth Elektronik WE-TVS bidirectional TVS diode, 5V standoff, 9V clamping, SOT-23 package. Protects two I/O lines for power and consumer electronics.
Add 60W amplification to your HiFiBerry DAC board. The AAmp60 powers the amp, DAC & Raspberry Pi via a 12-20V PSU. Requires compatible DAC.
Infineon ESD5V3U2U series protection device. 5.3V operating, 28V max clamping voltage in TSFP case. For circuit safeguarding.
