117528 products
Showing 15811-15840 of 117528 products
Microchip PIC32MM 32-bit Flash MCU, 25MHz, 256KB, TQFP 48 pin, rich interfaces & ADC. Ideal for embedded & IoT projects.
4-bit dual-supply non-inverting bus transceiver in TSSOP-16 package. Features voltage-level shifting (1.2V-3.6V) and IOFF support.
Diodes AP2112K-3.3TRG1 3.3V LDO voltage regulator with 600mA minimum output current, enable function and SOT-25-5 surface-mount package.
ONSEMI 74HC14 Hex Inverter Logic IC with Schmitt trigger input. 14-pin SOIC, 2-6V supply. Ideal for automotive & industrial noisy environments.
Learn Python & electronics with Programming ESP32 by Simon Monk. Covers ESP32 Lite & DevKit 1, sensors, WiFi & more. No prior knowledge needed.
Broadcom 2-channel Darlington optocoupler in DIP-8 package. Features 3.75kV isolation and 300% min CTR for signal processing and networking.
VISHAY H11D1 1-channel optocoupler with transistor output, DIP-6, 60mA, 5.3kV isolation. High BVCER, suitable for industrial networking.
BIVAR PLP5 transparent circular light pipe, 3.2mm. Press fit panel mount with UL94V-0 rating. Ideal for lighting applications.
Broadcom right angle RGB SMD LED with dome lens and 125° viewing angle. Ideal for back-lighting, status indication and front panel illumination.
Dialight 5mm RGB through hole LED, 20mA per colour with clear round lens and 50° viewing angle. For status indicators and PCB projects.
Reliable red 3mm LED lamp with 635nm wavelength, through-hole mount, and high light output for industrial use.
Wurth Elektronik WL-SBRW bi-colour SMD LED (Red/Green). 120° viewing angle, 1205 rectangular lens. Ideal for indicators & backlighting.
Expand serial ports with the DFROBOT Gravity I2C to Dual UART Module. Ideal for IoT, GPS, and ultrasonic projects. Supports up to 1Mbps data rate.
Pimoroni Breakout Garden Mini for Raspberry Pi. Features 2x I2C & 1x SPI slots for easy prototyping without soldering.
DFROBOT 2-in-1 USB-C to dual Micro USB cable, 1m. Compact and lightweight at 24g, ideal for charging and connecting devices.
Monitor water pressure from 0-1.6MPa with this IP68 Arduino-compatible analogue sensor. Ideal for IoT, smart homes, and environmental projects.
DFROBOT USB to TTL Converter with CP210x chip. 5V operation for APC220 radio modules & STC microcontroller programming.
ISOCOM 4N35XSM optocoupler for 5.3kV isolation. 1-channel transistor output in 6-pin SMD package for industrial & motor control.
High-density ISOCOM 1-channel optocoupler with NPN phototransistor output, 5.3kV isolation, and 4-pin DIP package for industrial use.
ISOCOM MOC3042XSM 6-pin SMD optocoupler with zero-crossing TRIAC output. 5.3kV isolation, 400V rating for motor & industrial controls.
ISOCOM TIL197 4-pin DIP optocoupler with 500% CTR & 5.3kV isolation. For computers, industrial & test equipment. Reliable signal transmission.
2.4GHz WiFi shield for Arduino UNO and Mega with pre-soldered ESP8266 module, TCP/UDP support and STA/AP modes.
Add 26 TOPS of AI power to your Raspberry Pi 5 with the AI HAT+. Features a Hailo accelerator for robotics, security & home automation.
Diodes Inc. US1G-13-F ultrafast rectifier, 400V, 1A, 50ns recovery. SMA package, ideal for aerospace, defence & power supplies.
Unidirectional SMCJ TVS Diode by Multicomp Pro. 30V standoff, 48.4V clamping, surface mount for industrial use.
PNP complementary power transistor by STMicroelectronics. 80V, 10A, 50W, TO-220 through-hole package. Ideal for industrial & power management.
VISHAY N-channel power MOSFET, 100V, 4.3A, in TO-252 (DPAK) package. Low 0.54ohm Rds(on) for efficient switching in power supplies and motor drives.
High-voltage VISHAY rectifier diode, 1.2 kV, 20 A, in a TO-220AC package. Low forward voltage drop for efficient input rectification.
Ultra-low profile aluminium heatsink for Raspberry Pi 5. Includes thermal pads & clips for easy installation in compact cases.
Protect your board with the black Cyntech Raspberry Pi Zero Case. Fully enclosed design with GPIO and camera slots.
