Showing 6151-6180 of 116085 items
Microchip
Microchip 10/100 Ethernet PHY transceiver IC in QFN-32 package. Features RMII, cable diagnostics & industrial temp range for embedded designs.
Texas Instruments
4-Channel low noise operational amplifier by Texas Instruments. 3MHz bandwidth, 7V-36V supply, SOIC-14 surface mount.
Texas Instruments 4-bit bus transceiver with voltage level shifting, 3.1ns delay, and Ioff for power-down. Ideal for industrial & portable devices.
Diodes Inc.
DIODES INC. synchronous buck converter: 3.8-32V input, 5V output, 2A, TSOT-26, EMI reduction for reliable power.
52Pi
Enhance your Raspberry Pi 5 with the 52Pi NVDigi audio board, featuring S/PDIF, M.2 NVMe slot, IR receiver, and high-res audio up to 192kHz.
Broadcom
BROADCOM 1-channel SOIC-8 optocoupler with 1Mbps speed, 3.75kV isolation & TTL output. For motor control, power interfaces & signal processing.
Isocom
ISOCOM 6-pin SMD optocoupler with Triac output, 5.3kV isolation. For motor control, consumer electronics & AC load switching.
APEM
APEM Q12 green LED panel indicator, 24 VDC, 12 mm hole, 20 mA, 60 mcd. Ideal for control panels and automation.
Broadcom subminiature high-efficiency red SMD LED, 626nm, wide viewing angle, ideal for space-limited industrial signalling.
CML
24V red LED panel indicator with matt chrome bezel and IP67 rating. For industrial signalling in control panels and machinery. 8mm mount.
Dialight
Durable Dialight green LED panel indicator for 24V systems. Watertight, high-intensity, and built for industrial, aerospace & automotive use.
VCC
VCC transparent light pipe for panel mounting. Transmits & blends LED light with a 160° viewing angle. Easy install.
DFRobot
Open-source prototyping shield for Arduino Mega & Due with reset button, power rails, and DIP area. Ideal for hobbyists and engineers.
Step down 12-24V to 5V with this efficient dual USB buck converter module. Features 3A output, overload protection, and stable power for DIY projects.
Compact DFROBOT holder for 6 AA batteries, featuring a DC 2.1mm power jack. Ideal for electronics projects, sensors & portable devices.
DFROBOT vertical adaptor converts RJ45 to an 8-position screw terminal block. Ideal for electronics prototyping & industrial wiring. 43x33x15mm.
Flexible DFROBOT liquid level sensor for non-conductive containers. Non-contact capacitive design with 3M adhesive tape & IP62 rating.
Pimoroni
Upgrade your projects with the PIMORONI Pico Plus 2. Features RP2350B, 8MB PSRAM, 16MB flash & USB-C. Compatible with Pico add-ons.
ISOCOM IS621XSM 6-pin SMD optocoupler with 5.3kV isolation & zero-crossing TRIAC output for motor control & industrial uses.
ISOCOM ISQ203X 4-channel optocoupler with 5.3kV isolation, 225% CTR, and DIP16 package for industrial and computer applications.
ISOCOM SFH615A-3X 1-channel optocoupler. 5.3kV isolation, 50mA forward current, 100% CTR. For industrial & computer systems.
Whadda
Whadda NodeMcu V2 Lua development board with ESP8266 WiFi. Perfect for IoT prototyping, featuring 10 GPIO pins & breadboard compatibility.
Amplify audio signals up to 8.5x with the Whadda WPM457 Digital Speaker Module. Features SC8002B chip, 2W power, 80dB volume & 5V DC supply.
Bourns
BOURNS SMCJ12A unidirectional TVS diode, 12V stand-off, 19.9V clamping. Protects power lines, automotive & industrial electronics from transients.
Littelfuse
Littelfuse axial leaded Schottky rectifier, 45V, 20A. Features 250A surge current & 150°C max operating temp. Ideal for power supplies.
RÖHM
Low forward voltage Schottky diode, 40V, 2A, SOD-106, ideal for motor control and portable devices.
Taiwan Semiconductor
Taiwan Semiconductor DBLS203G SMD bridge rectifier, 2A, 200V, single phase, surface mount.
VISHAY
VISHAY TRANSZORB SMCJ unidirectional TVS diode, 5V reverse standoff, 9.2V clamping, surface mount. Ideal for automotive & electronics protection.
Wurth Elektronik
Wurth Elektronik WE-TVS bidirectional TVS diode, 5V standoff, 9V clamping, SOT-23 package. Protects two I/O lines for power and consumer electronics.
Hifiberry
Add 60W amplification to your HiFiBerry DAC board. The AAmp60 powers the amp, DAC & Raspberry Pi via a 12-20V PSU. Requires compatible DAC.
