121221 products
Showing 16141-16170 of 121221 products
MICROCHIP MIC5205YM5: 150mA ultra-low noise LDO regulator with 165mV dropout, 1% accuracy & logic enable. Ideal for portable electronics.
TEXAS INSTRUMENTS LMC6482 dual CMOS op-amp with rail-to-rail I/O, 1.5MHz, 3V-15.5V, SOIC-8. Ideal for precision signal conditioning.
Texas Instruments TXS0102DCUR 2-bit bidirectional voltage level translator in VSSOP-8 package. Operates from -40°C to 85°C for mixed-voltage designs.
LNK304GN-TL off-line switcher IC in PDIP-8 package from Power Integrations. For buck, buck-boost and flyback designs under 360 mA.
Enhance your Raspberry Pi 5 with the 52Pi NVDigi audio board, featuring S/PDIF, M.2 NVMe slot, IR receiver, and high-res audio up to 192kHz.
Broadcom single-channel optocoupler, SOIC-8, 25mA, 3.75kV isolation and up to 1 Mbps. Suited to motor drive and power module interfaces.
Isocom MOC3020XSM SMD optocoupler with Triac output, 5.3 kV isolation and 400 V off-state voltage for AC load control.
APEM Q12 green LED panel indicator, 24 VDC, 12 mm hole, 20 mA, 60 mcd. Ideal for control panels and automation.
Broadcom subminiature high-efficiency red SMD LED, 626nm, wide viewing angle, ideal for space-limited industrial signalling.
CML LED panel mount indicator with red LED, matt chrome bezel, 24V DC operation, 8mm mounting hole and IP67 rating for panel installations.
Durable Dialight green LED panel indicator for 24V systems. Watertight, high-intensity, and built for industrial, aerospace & automotive use.
VCC transparent light pipe for panel mounting. Transmits & blends LED light with a 160° viewing angle. Easy install.
Open-source prototyping shield for Arduino Mega & Due with reset button, power rails, and DIP area. Ideal for hobbyists and engineers.
Step down 12-24V to 5V with this efficient dual USB buck converter module. Features 3A output, overload protection, and stable power for DIY projects.
Compact DFROBOT holder for 6 AA batteries, featuring a DC 2.1mm power jack. Ideal for electronics projects, sensors & portable devices.
DFROBOT vertical adaptor converts RJ45 to an 8-position screw terminal block. Ideal for electronics prototyping & industrial wiring. 43x33x15mm.
DFRobot non-contact capacitive liquid level sensor with flexible substrate, 3M adhesive mounting and digital output for walls up to 5 mm.
Upgrade your projects with the PIMORONI Pico Plus 2. Features RP2350B, 8MB PSRAM, 16MB flash & USB-C. Compatible with Pico add-ons.
ISOCOM IS621XSM 6-pin SMD optocoupler with 5.3kV isolation & zero-crossing TRIAC output for motor control & industrial uses.
Isocom ISQ203X 4-channel optocoupler in 16-pin DIP package with 5.3kVrms isolation, 225% minimum CTR and 70V BVCEO for signal isolation.
ISOCOM SFH615A-3X 1-channel optocoupler. 5.3kV isolation, 50mA forward current, 100% CTR. For industrial & computer systems.
Whadda NodeMcu V2 Lua development board with ESP8266 WiFi. Perfect for IoT prototyping, featuring 10 GPIO pins & breadboard compatibility.
Amplify audio signals up to 8.5x with the Whadda WPM457 Digital Speaker Module. Features SC8002B chip, 2W power, 80dB volume & 5V DC supply.
Bourns SMCJ12A unidirectional TVS diode, 12 V stand-off, 1500 W peak pulse power, DO-214AB (SMC) surface-mount package for surge protection.
Littelfuse axial leaded Schottky rectifier, 45V, 20A. Features 250A surge current & 150°C max operating temp. Ideal for power supplies.
Low forward voltage Schottky diode, 40V, 2A, SOD-106, ideal for motor control and portable devices.
Taiwan Semiconductor DBLS203G SMD bridge rectifier, 2A, 200V, single phase, surface mount.
VISHAY TRANSZORB SMCJ unidirectional TVS diode, 5V reverse standoff, 9.2V clamping, surface mount. Ideal for automotive & electronics protection.
Wurth Elektronik WE-TVS bidirectional TVS diode, 5V standoff, 9V clamping, SOT-23 package. Protects two I/O lines for power and consumer electronics.
Add 60W amplification to your HiFiBerry DAC board. The AAmp60 powers the amp, DAC & Raspberry Pi via a 12-20V PSU. Requires compatible DAC.
